Coupon code can only be used once per order. To receive the discount, enter PD20 in the coupon code box during checkout. Cannot be combined with any other coupon code.Ģ0% discount applies only to orders with the purchase of one HZ602, one HD112 or one HD113 model available from. 25% discount is applied to order subtotal, before shipping and taxes, and is limited to the purchase of one IZ441HBRN or one WD101 available from. To receive the discount, enter PD25 in the coupon code box during checkout. Cannot be combined with any other coupon code.Ģ5% discount applies only to orders with the purchase of one IZ441HBRN or one WD101 model available from. 30% discount is applied to order subtotal, before shipping and taxes, and is limited to the purchase of one RV2502AE available from. To receive the discount, enter PD30 in the coupon code box during checkout. Orders cannot be shipped to PO boxes or Hawaii, Alaska, Puerto Rico or other territories outside of the contiguous 48 states.ģ0% discount applies only to orders with the purchase of one RV2502AE model available from. SharkNinja reserves the right to cancel or modify this offer at any time. This offer is not valid with any prior purchases. I'm using Samsung EVO 840 SSDs connected via SATAIII to the native ports on the mobo.Promotion valid on through February 20th, 2023, at 11:59pm ET, while supplies last. It's like the system sees that I haven't used the sample and just decides to unload it. Then, as the day progresses, if I haven't used a sample for a long period of time, this needs to happen again. It's like my hard drive needs to "wake up". Once I've played it back everything works perfectly. When I first play back my song, every note just pops and clicks. I've also noticed lately that my samples seem to get "dynamically" loaded and unloaded from RAM. Still not sure what's happening with problem #2 though. In fact it even takes a bit longer to load (aprox. My template with all cells disabled takes up almost the same amount of RAM as when all cells are enabled. I am experiencing the exact same thing in Windows 7. I just ran the test agaon and memory went from 38 GB to 21 GB. Apparently I had "Force Enabled Cells" checked in VIPro, and so VEP was loading all cells disabled then enabling them. I never checked to make sure that the cells were in fact disabled. I just don't want to run a third-party app five times to get to that starting point.Īll thoughts welcome, with VSL's tech gurus in particular.ĮDIT: I'm an idiot. And it's great to have such a full template at the ready, starting at 16.71 GB ready to load. Needless to say, the goal of a large template with disabled cells is to start from the lowest possible RAM footprint and work up. Why, outside of the program itself and the loaded settings, does a disabled VE Pro need any more RAM at all? I don't understand why VE Pro loads with cells disabled, and yet takes up so much memory. These are run successively, without doing anything to VE Pro. But the Activity Monitor on my Mac says that VE Pro is holding 14.25 GB (with 4.25 Free on whole computer, with other programs running).Įnter a free, downloadable app called "Memory Clean." Note the GB numbers in the following five runs of the Memory Clean program. So I load my metaframe with all cells disabled.Īfter the load, all cells are indeed disabled. Simply enable the cells as you go, when you need the additional articulations." This way you may load a matrix or preset containing all possible articulations while keeping memory footprint low. When a cell is disabled, all its samples are cleared from memory, while settings are kept intact. The VSL manual states, " A powerful new feature called Disabled Cells offers disabling and enabling cells of a matrix. I have a metaframe load of twenty instances, all on an SSD. This is a reboot of a thread that did not gain traction.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |